• Description
  • Specs
  • Method
  • Safety
  • The Bellman Milk Steamer gives you the power to steam silky-smooth textured milk at home for your milk-based espresso drinks. By heating the unit on your stove, you're able to create enough pressure to steam milk (dairy or non-dairy) using the steam wand with a built-in 2-hole tip. You'll be enjoying smooth, creamy café quality drinks at home or while travelling.

    The Bellman CX-25 series can be used on gas, electric, open flame and most induction stovetops. Compact and easy to use. Create professionally steamed milk on the go - the Bellman is perfect for camping and travel! Entertaining? The Bellman can steam enough milk for a few drinks in a row.

    • Material: 18/8 stainless steel
    • Handle and Knob: Bakelite
    • Width: 16 cm
    • Length: 21 cm
    • Height: 21 cm
    • Weight: 1.6 kg
  • To Steam Milk with the Bellman Milk Steamer:

      • Unscrew Knob and remove the head piece.
      • Fill the body with cold water (below the handle line).
      • Replace head piece and tighten knob.
      • Place steamer on medium high heat on the stovetop. Allow the machine to heat for 3-5 minutes -until there is sufficient pressure in the boiler.
      • Open the steam valve for a few seconds to bleed water inside the steam wand.
      • If the steam doesn't produce a strong, steady hiss, raise the heat slightly.
      • If the steam explodes from the tube at half a turn of the knob, reduce the heat.
      • Froth milk: Fill a milk pitcher 1/3 full with cold milk.
      • Immerse the steam wand into the milk.
      • Slowly open the steam valve until you have a strong flow of steam.
      • Move the steam wand up as the froth builds.

    To Clean the Bellman Milk Steamer:
      • Open the steam valve and release the pressure
      • Let the machine body cool down
      • Clean milk from the steam tube
  • Please read for your safety

    The bottom o-ring of CX-25 series (CX-25S, CX-25, CX-25P) is very important. The device may explode if the screw is not fixed correctly. DO NOT REPLACE THE BOTTOM O-RING by yourself if you don't have proper tools to replace it.

    Please pay close attention when replacing the BOTTOM O-RING. Prepare an electronic or air compressing tool to release and lock the nut of the bottom of CX-25 series. Holding the main body tightly, the torque of locking the nut of the bottom of CX-25 series should be 6~8 kgs. Too much torque may damage the screw. The hole at the bottom of CX-25 series is not circle shaped. The shape is for fitting the shaft screw. Please make sure the lines of these two parts are aligned correctly before locking the nut of the bottom of CX-25 series.

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
J
J.K.
Works great, simple to use

A great compact device to get that desired latte foam texture in-house, without having to shell out for an expensive espresso machine. Actually very simple to use, parts fit together logically and includes step by step instructions on assembly. Once it's full it can be used several times before needing to be disassembled for refill.

Can take a little while (5 mins or so) to get up to steaming temperature so best to start heating it before brewing the coffee. Overall a nice addition to the kitchen that's found a permanent home on my stovetop. 10/10.

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
J
J.K.
Works great, simple to use

A great compact device to get that desired latte foam texture in-house, without having to shell out for an expensive espresso machine. Actually very simple to use, parts fit together logically and includes step by step instructions on assembly. Once it's full it can be used several times before needing to be disassembled for refill.

Can take a little while (5 mins or so) to get up to steaming temperature so best to start heating it before brewing the coffee. Overall a nice addition to the kitchen that's found a permanent home on my stovetop. 10/10.

x